Bipac 5200 SR2 Bridge Mode To Router

Billion Bipac 5102SR ไม่ต้อง up firmware ก็ set ให้เป็น router ได้

1. set lan card ให้เป็น 192.168.1.3
2. เรียก IE ขึ้นมาใส่ address http://192.168.1.1
Username : true
Password : true
3. http://192.168.1.1/maintenance/tools_system.htm
4. ป้อน password ใหม่ 2 ครั้ง
Username : admin
Password : admin
5. ปิดแล้วเปิด modem ใหม่
6. เรียก IE ขึ้นมา ใส่ address http://192.168.1.1
Username : admin
Password : ที่คุณใส่ไว้ในข้อที่ 4.

เท่านี้คุณก็จะเข้าไปที่หน้าของการ config แบบ admin ได้ทั้งหมด
หรือ
คุณอาจเข้าไปconfig ผ่าน telnet ก็ได้

ซึ่งถ้าคุณ telnet เข้าไป มันจะถาม password
ก็ให้พิมพ์ password = ที่คุณใส่ไว้ในข้อที่ 4.

ต่ออีกนิด
หลังจากที่เข้าไปเป็น admin ได้แล้ว
ให้ ser parameter (สำหรับ true)
ให้เข้าไปที่ Interface setup -> internet ตั้งค่า parameter เป็น
virtual circuit = PVC0
Status = activated
vip = 0
vci = 100

ATM Qos = UBR
PCR = 0
SCR = 0
MBS = 0

ISP = PPPoE/PPPoA
Username : username ของ คุณ ที่ได้จาก true
Passward : password ของ คุณ ที่ได้จาก true
encapsulation = PPPoE LLC

connection = always on
Tcp MSS Option = 0 byte

Get ip address = Dynamic
static Ip address = 0.0.0.0
ip subnet mask = 0.0.0.0
gateway = 0.0.0.0
nat = Enable (ถ้าหากต้องการ forward port)
Default route = Yes
Dynamic Route = RIP1
Direction = None
Multicast = Disabled
save

เข้าไปที่ Interface setup -> lan ตั้งค่า parameter
ip address=192.168.1.1
ip subnet mask = 255.255.255.0
Dynamic route = RIP1
Direction = None
Multicast = Disable

DHCP = Enabled (เมื่อต้องการให้ router แจก IP ให้กับเครื่องคอม)
Starting Ip Address = 192.168.1.101
ip Pool count = 100
lease time = 86400
DNS relay = Use auto discovered DNS server only
Primary DNS Server = N/A
Secondary DNS Server = N/A
save

เข้าไปที่ Maintenance -> SysRestart -> Current Settings -> RESTART

ช่วงที่รอ router boot ใหม่ ก็ให้ไปเปลี่ยน tcp/ip ของ LAN card เป็น
Obtain an IP address automatically



คลิ๊กที่ Properties



เลือก Internet Protocol (TCP/IP) แล้วคลิ๊ก Properties ครับ

เลิอกเป็น Obtain an IP address automatically

ขอให้สำเร็จครับ

ปล. ถ้าเบื่อก็ให้ไปที่ http://192.168.1.1/maintenance/tools_system.htm
ให้ไปเลือกที่ factory default แล้วก็ ปิดเปิด modem ใหม่
คุณก็จะด้ระบบเดิมที่เป็น Bridg mode กลับคืนมา เหมือนเดิม

Credit By
Pix : The Lord Of Wireless Website
Source : Mr.mmc
Modified : Junma

FM 106 ครอบครัวข่าว